Buenas Noches Comunidad tenia el mismo problema con el failed-to-start-light-display-manage y la forma de solucionarlo fue utilizar una tarjeta grafica integrada a la Board y una vez instalado el SO:
Utilice esta ayuda :
TOTAL CREDITS A ==>>> https://docs.kali.org/general-use/install-nvidia-drivers-on-kali-linux <===
–//—
First, you’ll need to ensure that your system is fully upgraded and that your card supports CUDA.
Note: GPUs with a CUDA compute capability > 5.0 are recommended, but GPUs with less will still work.
apt update && apt dist-upgrade -y && reboot
Let’s determine the exact GPU installed, and check the kernel modules it’s using.
root@kali:~# lspci -v
01:00.0 VGA compatible controller: NVIDIA Corporation GM204 [GeForce GTX 970] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ZOTAC International (MCO) Ltd. GM204 [GeForce GTX 970]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [78] Express (v2) Legacy Endpoint, MSI 00
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024
Kernel driver in use: nouveau
Kernel modules: nouveau
Installation
Once the system has rebooted, we will proceed to install the OpenCL ICD Loader, Drivers, and the CUDA toolkit.
apt install -y ocl-icd-libopencl1 nvidia-driver nvidia-cuda-toolkit
During installation of the drivers the system created new kernel modules, so another reboot is required.
Verify Driver Installation
Now that our system should be ready to go, we need to verify the drivers have been loaded correctly. We can quickly verify this by running the nvidia-smi tool.
root@kali:~# nvidia-smi
+-----------------------------------------------------------------------------+
| NVIDIA-SMI 375.26 Driver Version: 375.26 |
|-------------------------------+----------------------+----------------------+
| GPU Name Persistence-M| Bus-Id Disp.A | Volatile Uncorr. ECC |
| Fan Temp Perf Pwr:Usage/Cap| Memory-Usage | GPU-Util Compute M. |
|===============================+======================+======================|
| 0 GeForce GTX 970 Off | 0000:01:00.0 On | N/A |
| 36% 46C P0 47W / 325W | 200MiB / 4036MiB | 0% Default |
+-------------------------------+----------------------+----------------------+
+-----------------------------------------------------------------------------+
| Processes: GPU Memory |
| GPU PID Type Process name Usage |
|=============================================================================|
| 0 692 G /usr/lib/xorg/Xorg 198MiB |
+-----------------------------------------------------------------------------+
With the output displaying our driver and GPU correctly, we can now dive into benchmarking. Before we get too far ahead, let’s double check to make sure hashcat and CUDA are working together.
root@kali:~# hashcat -I
OpenCL Info:
Platform ID #1
Vendor : NVIDIA Corporation
Name : NVIDIA CUDA
Version : OpenCL 1.2 CUDA 8.0.0
Device ID #1
Type : GPU
Vendor ID : 32
Vendor : NVIDIA Corporation
Name : GeForce GTX 970
Version : OpenCL 1.2 CUDA
Processor(s) : 13
Clock : 1240
Memory : 1009/4036 MB allocatable
OpenCL Version : OpenCL C 1.2
Driver Version : 375.26
It appears everything is working, let’s go ahead and run a benchmark test.
Benchmarking
root@kali:~# hashcat -b
OpenCL Platform #1: NVIDIA Corporation
======================================
* Device #1: Geforce GTX 970, 1009/4095 MB allocatable, 13MCU
Hashtype: MD5
Speed.Dev.#1.....: 10443.1 MH/s
Hashtype: SHA1
Speed.Dev.#1.....: 3349.8 MH/s
Hashtype: SHA256
Speed.Dev.#1.....: 1321.8 MH/s
There are a multitude of configurations to improve cracking speed, not mentioned in this guide. However, we encourage you to take a look at the hashcat documentation for your specific cases.
Troubleshooting
In the event setup isn’t going as planned, we’ll install clinfo for detailed troubleshooting information.
apt install -y clinfo
OpenCL Loaders
It may be necessary to check for additional packages that may be conflicting with our setup. Let’s first check to see what OpenCL Loader we have installed. The NVIDIA OpenCL Loader and the generic OpenCL Loader will both work for our system.
root@kali:~# dpkg -l |grep -i icd
ii nvidia-egl-icd:amd64 375.26-2 amd64 NVIDIA EGL installable client driver (ICD)
ii nvidia-opencl-icd:amd64 375.26-2 amd64 NVIDIA OpenCL installable client driver (ICD)
ii nvidia-vulkan-icd:amd64 375.26-2 amd64 NVIDIA Vulkan installable client driver (ICD)
ii ocl-icd-libopencl1:amd64 2.2.11-1 amd64 Generic OpenCL ICD Loader
If mesa-opencl-icd is installed run:
apt remove mesa-opencl-icd
Since we have determined that we have a compatible ICD loader installed, we can easily determine which loader is currently being used.
root@kali:~# clinfo | grep -i "icd loader"
ICD loader properties
ICD loader Name OpenCL ICD Loader
ICD loader Vendor OCL Icd free software
ICD loader Version 2.2.11
ICD loader Profile OpenCL 2.1
As expected, our setup is using the open source loader that was installed earlier. Now, let’s get some detailed information about the system.
Querying GPU Information
We’ll use nvidia-smi once again, but with a much more verbose output.
root@kali:~# nvidia-smi -i 0 -q
Driver Version : 375.26
Attached GPUs : 1
GPU 0000:01:00.0
Product Name : GeForce GTX 970
Product Brand : GeForce
Display Mode : Enabled
Display Active : Enabled
Persistence Mode : Disabled
Accounting Mode : Disabled
Accounting Mode Buffer Size : 1920
Temperature
GPU Current Temp : 47 C
GPU Shutdown Temp : 96 C
GPU Slowdown Temp : 91 C
Clocks
Graphics : 1101 MHz
SM : 1101 MHz
Memory : 3523 MHz
Video : 1012 MHz
Processes
Process ID : 692
Type : G
Name : /usr/lib/xorg/Xorg
Used GPU Memory : 198 MiB
It looks like our GPU is being recognized correctly, so let’s use glxinfo to determine if 3D Rendering is enabled.
root@kali:~# glxinfo | grep -i "direct rendering"
direct rendering: Yes
The combination of these tools should assist the troubleshooting process greatly. If you still experience issues, we recommend searching for similar setups and any nuances that may affect your specific system.
TOTAL CREDITS A https://docs.kali.org/general-use/install-nvidia-drivers-on-kali-linux